IHC/IHC Digest Archive

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: [ihc] Re: ihc-digest V7 #439



My understanding has always been that an IH T-19 was an IH T-19 was an
IH T-19 as far as the front end was concerned.  That when a 258 was to
go in, they just used a bellhousing set up for an AMC rather than the
one for an SV.  I have a T-19 that came out of a 258 equipped truck (150
or 100) that I parted out.  I unfortunately I don't have a loose T-19
from behind an SV or 196 to compare to.  Somebody give me some
measurements and I will check the front end out. 

My impression of what Pete needs to do on the front end of the tranny is
drill the other two holes out of the T-18 bellhousing to mate it to the
T-19.  There are two holes above and 4 holes below the hole in the
center.  I believe they are in a straight line up and down on either
side. The top ones are the same for T-18 and T-19.  The next ones down,
roughly making a square with the top two are for a T-18.  Below them,
making a rectangle with the top two, are two bosses where the holes need
to be for a T-19.  Input shafts are the same in every way no matter AMC
or SV.  Drill out the bosses and bolt it up.  

Maybe I have believed wrong for years.  I will compare the T-19 with a
T-98s I have around. The only other T-19 I have is still between a Dana
20 and a 196.  

Someone else will have to help with the back end and the connection with
the T-case.  I've never messed with a single speed.  

Ed

   

-----Original Message-----
From: owner-ihc@domain.elided [mailto:owner-ihc@domain.elided] On Behalf Of
salmineo@domain.elided
Sent: Tuesday, April 27, 2004 10:08 AM
To: ihc@domain.elided
Subject: [ihc] Re: ihc-digest V7 #439


Peter, I had looked at doing this once upon a time.  The answer is yes
and no.  AMC used several input shafts on the same application T-18,
according the transmission parts suppliers I talked with.  In an effort
to use as much existing inventory on new cars and trucks, they used
several different adaptors along with several different bellhousingsn
depending on what was on the shelf, so it may work, depending on whether
you get lucky and get the correct length input shaft along with the
correct depth bellhousing (there were 4 that AMC used) along with the
correct bellhousing adaptor (mounts between the bellhousing and the
transmission).  Do not just go out and get the first transmission you
find, or the first bellhousing you find, because chances are it will not
work unless you did the proper measurements and comparisons.  If you
have a T-19 already, then maybe you could find a Jeep transmission that
still has the bellhousing and adaptor with it, and measure the length of
the input shaft to see if it is the same, in which case that bellhousing
may fit.  Of course you still have to make sure the crank pilot does not
stick back further than the engine the transmission came from, else you
may bottom out the Jeep input before it is tightened down to the block.

Your post was kind of confusing:  are you talking about putting an AMC
360 in a Scout using an IHC T-19?  What exactly is it you are proposing?
-Colin Rush

Date: Mon, 26 Apr 2004 13:28:36 -0700
From: "Peter  Shubin" <pshubin@domain.elided>
Subject: [ihc] Manual Transmission Differences T-18 & T-19 for Various
Engines & 
Transfer Cases

I need a little help and know someone can answer this off the top of
their
head.  

 

What are the differences between the T-18 and T-19 transmissions that
were
used in Scouts for the 258 I-6, 345, and 192?

 

What are the differences between the T-19s that have a Dana 20 bolted to
the
rear and those that have a single speed transfer case?

 

Would a Scout with a 192 most likely get a granny low T-19 or a close
ration
T-19?

 

If you are curious I am wondering if I can take a 258 (now 360), AMC
bolt
pattern T-18 bell housing, T-18, Dana 20 setup and make a 360, AMC bolt
pattern T-18 bell housing, T-19, Dana 20 setup by using my current
set-up in
my '72 and mixing it with parts from a '78 Scout with a 192, T-19, and
single speed transfer case.  These are all Scout II parts.  Or simply,
can I
swap a T-19 for a T-18 and not have to find any additional parts?


________________________________________________________________
The best thing to hit the Internet in years - Juno SpeedBand!
Surf the Web up to FIVE TIMES FASTER!
Only $14.95/ month - visit www.juno.com to sign up today!


Home | Archive | Main Index | Thread Index